IS200RAPAG1BBA Company - GE DS200TCEBG1A DS200TCEBG1ACE Common Circuits EOS Card – RuiMingSheng
IS200RAPAG1BBA Company - GE DS200TCEBG1A DS200TCEBG1ACE Common Circuits EOS Card – RuiMingSheng Detail:
Description
| Manufacture | GE |
| Model | DS200TCEBG1A |
| Ordering information | DS200TCEBG1ACE |
| Catalog | Speedtronic Mark V |
| Description | GE DS200TCEBG1A DS200TCEBG1ACE Common Circuits EOS Card |
| Origin | United States (US) |
| HS Code | 85389091 |
| Dimension | 16cm*16cm*12cm |
| Weight | 0.8kg |
Details
The DS200TCEBG1ACE Protective Termination Expander Board features 3 bayonet connectors, 4 signal transformers and 1 26-pin connector along with 4 10-pin connectors and 3 20-pin connectors. Each of the bayonet connectors are labeled JWX, JWY, and JWZ on the board. Users are able to connect to the male bayonets however guidelines must be followed to ensure safety. To connect a bayonet connector to the board, align it with the connector on the board and press it into place.
To disconnect a cable with a bayonet connector, grasp the connector with your thumb and one finger while supporting the board with your other hand and firmly pull to disconnect. When replacing connectors it is best practice to label the conections to make it easy to locate them and reattach to the new board after installation.
Interference occurs when power cables produce too much energy and run too close to signal cables. If signals are not being transmitted or received accurately, the drive will not operate effectively. Air flow cools the components of the drive and increases the length of time between when the components must be replaced. Ensure that the drive is stored in a cool and clean location.
The GE Protective Termination Expander Board DS200TCEBG1A features 3 bayonet connectors, 4 signal transformers, and 1 26-pin connector. It also contains 4 10-pin connectors and 3 20-pin connectors.
Because the GE Protective Termination Expander Board DS200TCEBG1A is populated with multiple heavy components it is designed with 8 screws holes to support the weight of the board when it is installed in the drive. Before you begin the task of removing the old board, notice where the old board is installed and plan to install the replacement board in the same location.
Also notice where the cables are connected in the drive and create tags or labels with the ID of the connector it is connected to on the board. Only when you document where the cables attached to the new board can you disconnect them.
Use a screwdriver to remove the screws that secure it in the drive. Use one hand to turn the screwdriver and use the other hand to support the board in the drive. Keep all the screws and washers that you remove.
If any screws drop into the bottom of the drive interior, retrieve the hardware before you proceed. A loose screws might make contact between electrical components and cause a short or electric shock or fire. This could lead to injury or extended downtime for the drive if additional repairs are required. If a screw is caught in a moving part, it might prevent the free movement of the part and cause damage to the motor or other parts.
Datasheet link
Product detail pictures:
Related Product Guide:
"Control the standard by the details, show the toughness by quality". Our firm has strived to establish a highly efficient and stable workers workforce and explored an effective high-quality management system for IS200RAPAG1BBA Company - GE DS200TCEBG1A DS200TCEBG1ACE Common Circuits EOS Card – RuiMingSheng , The product will supply to all over the world, such as: UAE, Vancouver, Peru, Taking the core concept of "to be the Responsible". We will redound up on society for high quality products and good service. We will initiative to participate in international competition to be a first- class manufacturer of this product in the world.
By Adelaide from Bangladesh - 2017.08.18 18:38
This manufacturer can keep improving and perfecting products and service, it is in line with the rules of market competition, a competitive company.
By Laura from Hanover - 2017.12.31 14:53
